What Floor Graphics Are Used For
Floor graphics are printed and cut decals made to sit on smooth walking surfaces for a set period of time. They are used for sale messages, directional arrows, social distancing prompts, safety warnings, queue control and branded event messaging. In busy spaces they work because people naturally look down when they walk, so the message gets seen without taking up wall or window space.
We supply floor decals for indoor use and for sheltered outdoor areas where the surface is clean and the traffic is controlled. For Bloemfontein winters, dusty entrances and the dry Free State air, the right material choice matters because dirt at the edges will shorten the life of any decal. If you need something for a reception, corridor, retail aisle or school passage, floor graphics are often the neatest option.
- Promotions at entrances, tills and aisle ends
- Route marking in factories, schools and clinics
- Queue guidance for waiting areas and service points
- Safety notices near stairs, ramps and wet floors
Sizes, Shapes And Finishes We Can Produce
Floor graphics can be made in almost any size, from a small 300 x 300 mm reminder mark to a full walkway strip or large branded panel. Common shapes include circles, rectangles, arrows, footprints, corner markers and custom cut shapes that follow a logo or message. If the area needs a repeated pattern, we can space the decals in a measured sequence so they alighn with the route or aisle layout.
We usually work from your measurements, or we can do a site survey in Bloemfontein, Mangaung, Botshabelo, Thaba Nchu, Welkom or Kroonstad. If you are unsure about size, we look at viewing distance, pedestrian flow and how much information the message must carry. A short instruction can be quite small, but a queue marker or directional sign needs enough width for clear reading from standing height.
- Custom cut to shape or supplied as standard rectangles and circles
- Matt or low glare finish for better foot-level visibility
- Printed graphics with cut vinyl text where required
- Clear edge placement options for subtle branding
Where Floor Decals Work Best
These graphics suit tiled floors, sealed concrete, polished surfaces, epoxy coatings and other smooth, clean areas. They are commonly used in retail shops, pharmacies, schools, churches, warehouses, trade counters, exhibition stands and municipal or office buildings. For coastal sites this product also helps where signage must be kept low and out of the wind, though the floor surface still needs proper prep.
We do not recommend applying floor graphics to rough, dusty, soft or damp surfaces. In a busy site around Hamilton or central Bloemfontein, a floor decal is only as good as the cleaning before installation. If the floor has loose paint, old adhesive or heavy texture, it may need preparation first. The same applies where loads of foot traffic, trolley wheels or cleaning chemicals are involved.
- Retail entrances and aisle directions
- Warehouses and loading areas
- Schools, halls and sports venues
- Clinics, offices and service counters
Installation And Site Conditions To Plan For
Floor graphics are installed by cleaning the surface thoroughly, confirming position, then applying the decal with even pressure so the edges bond properly. For larger runs we often mark out the route first, especially where there are multiple turns or numbered points. Installation can usually be done quickly with limited disruption, although a busy public area may need after-hours work or a short temporary closure.
No power or gas is needed for the product itself. If you are using illuminated displays or powered stands nearby, that is separate from the floor graphic. We can also fit matching wall, door or window graphics at the same time so the message stays consistent from the entrance to the till point. For sites affected by load-shedding, this is useful because floor signage stays visible without any electrical supply.
- Best installed on clean, dry, sealed surfaces
- No mains power or gas required
- Can be scheduled around trading hours
- Useful for temporary or longer term campaigns
Care, Cleaning And Service Life
To keep floor graphics looking good, they should be cleaned with a damp mop or cloth and a mild cleaner that is suitable for the floor finish. Avoid harsh solvents, abrasive pads and very heavy scrubbing on the edges. In high-traffic areas, the service life depends on shoe traffic, trolley movement and how often the surface is washed. A sheltered indoor entrance usually lasts longer than a rough passage that gets constant dirt from outside.
We also offer replacement, removal and refurbishment when messages change. If a promotion ends, the decal can be lifted off and the floor prepared again for a new layout. That is handy for seasonal specials, safety changes or queue systems that need updating. If the floor coating changes or starts to lift, it is better to sort it out early rather than leave a damaged edge to collect grime.
- Use mild cleaner and soft mop only
- Do not scrub edges with abrasive tools
- Check for lifting in corners and high-wear zones
- Plan for replacement when campaigns change
What To Check Before You Order
Before ordering floor graphics, decide exactly where they will go, how long they must last and what the message must say. Measure the area, note the walking direction and tell us if the surface is tile, sealed concrete or another finish. It also helps to confirm if the space is indoors, under cover or exposed to moisture. If the floor is often cleaned with strong chemicals, say so at the start because that affects material choice.
Please also check whether the graphic must show a logo, arrow, warning symbol, numbered point or simple text. If you already have artwork, send the file size and format if possible. If not, we can assist with artwork setup and logo redraws. For businesses in Mangaung, Botshabelo, Thaba Nchu, Welkom and Kroonstad, a brief site description and a couple of measurements are usually enough to start. That saves time and helps avoid reprints.
- Surface type and condition
- Indoor, outdoor or sheltered placement
- Exact size and quantity needed
- Message, logo and direction of travel
Key facts
| Material | Printed self-adhesive vinyl with slip-aware overlaminate for floor use |
|---|---|
| Size range | Small markers from 300 x 300 mm up to large custom walkway graphics |
| Finish | Matt or low glare |
| Use areas | Indoor floors and sheltered pedestrian areas on smooth sealed surfaces |
| Installation | Surface cleaned, measured and applied by trained installers |
| Service options | Removal, replacement, refurbishment and maintenance visits |
