What correx boards are used for
Correx boards are fluted plastic sign boards printed for short-term use. They are light enough to carry by hand, simple to fasten to fences or walls, and cost-effective when you need a clear message for a limited period. In Bloemfontein, they are often used for election messaging, site notices, school events, estate launches, promotions, and directions at functions where people need to see the message quickly.
The board itself is made for indoor and outdoor use, but it is best suited to temporary work rather than long-term exposure. For a campaign that runs for a few weeks, or a notice that only needs to stay up for a season, correx gives you a neat finish without the weight of a rigid board. It also holds up well in dusty Free State conditions, where a paper poster would not last long at all.
Because the surface is print-friendly, we can produce simple text boards, full-colour graphics, arrow signs and repeat notices in matching sizes. If your site has a lot of wind or a rough fence line, we can advise on fixing points and edge protection so the board stays put and does not flap or tear at the corners.
Sizes, thicknesses and print options
Most correx boards are supplied in practical sheet sizes that suit standard artwork layouts and easy handling. Common sizes include 600 x 900 mm, 900 x 1200 mm and 1200 x 2400 mm, with custom cuts available for tighter spaces or repeated sign runs. We can also produce smaller boards for directional messages, door notices or estate rules, and larger boards for roadside visibility.
Typical thickness options are 3 mm and 5 mm, depending on where the board will be used and how much support it will have. A 3 mm board works well for short runs, while a 5 mm board is a better choice where the board needs a bit more body, especially outdoors. Printing can be single-sided or double-sided, and we can add eyelets, drilling points or adhesive backing where needed.
- Single-sided print for walls, windows, doors and fixed fence lines
- Double-sided print for traffic-facing notices and directional boards
- Die-cut shapes for logos, arrows or campaign graphics
- Numbering, repeat artwork and same-size batch production
- Matte or gloss finish depending on the look you want
If you need a consistent set across several suburbs, we can keep the same artwork, colour and sizing through a full campaign. That helps when you are installing boards in Bloemfontein one week and Botshabelo or Thaba Nchu the next.
Where correx boards work best
Correx boards suit places where people need a clear, temporary message and the sign may need to come down again soon. They work well for event venues, school gates, sports days, church functions, property show days, retail promotions and municipal or community notices. For elections and public messaging, they are easy to place in rows and replace when details change.
They are also useful on building sites and short-term commercial work. If you need a board for a contractor notice, safety reminder or access instruction, correx is easy to mount and remove. In windy areas around Bloemfontein and the Free State, we often recommend extra fixing points, especially on open fencing or at exposed corners where gusts can catch the board.
- Campaign and election signage
- Event directions and parking notices
- School, church and community announcements
- Short-term retail specials
- Site notices and project information
For long exposure on a busy roadside, we may suggest another substrate if the board must last for many months. But for temporary messages, correx is usually the most practical option and keeps the job neat without overcomplicating the install.
Installing correx boards on site
Installation depends on where the board will sit. On fences, we normally use cable ties, wire or clips through pre-drilled points. On walls or doors, a suitable adhesive or mechanical fixing may be used, provided the surface is clean and dry. For indoor events, the boards can also be mounted on frames or freestanding supports. If the venue has a lot of foot traffic, we make sure the board is fixed high enough to avoid knocks and rubbing.
We do site surveys when needed, especially if the board must fit around gates, rails or uneven surfaces. That helps with sizing, fixing method and placement before production starts. It also reduces waste, which matters when you are ordering several boards at once. On some jobs we install same day, but for larger runs or if artwork still needs setup, we prefer a little lead time so the print and finishing are done properly.
Correx boards do not need power or gas on site, which makes them useful for areas where electricity is not reliable or where the venue has limited access. That is handy during load-shedding, at outdoor events and at temporary sites where you simply need a sign that can go up without extra equipment.
How to care for temporary boards
Correx is low-maintenance, but a little care helps it last through the full term of use. Keep the printed face clean with a soft cloth and mild soapy water. Avoid harsh solvents, abrasive pads or high pressure washing, as these can mark the print and lift edges. If a board is moved often, carry it flat rather than bending it. It will flex a little, but repeated bending can crease the flutes and weaken the panel.
For outdoor use, check the fixings now and then, especially after wind or rain. If a board loosens, it can flap, scrape or come adrift at the corners. In dusty areas, a quick wipe keeps the message readable and avoids a dull film building up on the surface. Small scratches and pin holes are normal on temporary work, but if the board is being reused several times it is worth storing it flat and away from direct sun when not in use.
If you need replacement boards during a campaign or notices need updating mid-run, we can help with reprints and maintenance visits. That is often easier than trying to patch old material that has already faded or warped a bit.
What to check before you order
Before ordering correx boards, check the message, the viewing distance and the fixing location. A board that will be read from across a street needs bigger type and fewer words than a notice at a doorway. If the artwork includes logos, small print or contact details, those elements need to stay legible at the chosen size. It is also worth confirming whether the board will be viewed in portrait or landscape layout, because that affects the whole design.
- Final wording, spelling and dates
- Exact size needed for the site
- Single-sided or double-sided print
- Indoor or outdoor placement
- Fixing method and surface type
- Quantity needed for each location
We can help with artwork setup, logo redraws and production checks before printing starts. If you already have artwork, send the file in good quality and tell us the finished size. If not, we can prepare the layout so the boards match across all your sites in Bloemfontein, Mangaung, Welkom, Kroonstad or Brandfort. A small typo on a temporary board can still cause confusion, so it is worth checking the copy carefully before sign-off.
Correx boards supplied from Hamilton, Bloemfontein
Central Signs works from Hamilton in Bloemfontein and serves the surrounding region with practical sign work that suits local conditions. Our team handles the full process from artwork and print production to cutting, finishing and installation. For correx boards, that means you get a clean, temporary sign that is easy to use and easy to remove when the job is done.
Whether you are organising a campaign, setting up an event, or posting short-term notices at several sites, we can supply boards in the quantity and size you need. We also work across Mangaung, Botshabelo, Thaba Nchu, Welkom and Kroonstad, so if your boards need to go out to more than one location, we can plan the run accordingly.
To place an order, send through the details via the enquiry form on our contact page and include your size, quantity and preferred fixing method. We will come back with the practical options, and if the site needs a check first, we can arrange that too.
Key facts
| Product type | Printed fluted plastic boards for temporary indoor and outdoor signage |
|---|---|
| Common thickness | 3 mm and 5 mm |
| Typical sizes | 600 x 900 mm, 900 x 1200 mm, 1200 x 2400 mm or custom cut |
| Print options | Single-sided or double-sided full-colour print |
| Fixing methods | Cable ties, wire, clips, adhesive or frame mounting |
| Best use period | Short-term campaigns, events, notices and seasonal promotions |
